AQUA MIX NANOSCRUB™ is an abrasive cream cleaner designed to work where other cleaners won’t. It utilizes NanoSTG™ (nano-sized particles) to penetrate below tough stains, dissolve and lift them out. Especially effective for cleaning rough or textured surfaces. Also removes factory applied waxes and floor finishes, coating sealers, light grout residue (including epoxy), rubber and pencil marks, light mineral deposits, ground-in dirt and most sealer residues. NanoScrub™ is nontoxic, non-flammable and non-acidic.
DESCRIPTION:
AQUA MIX NANOSCRUB® is an abrasive cream cleaner designed to work where other cleaners won’t. It utilizes NanoSTG™ (nano-sized particles) to penetrate into small surface pores where it can effectively work to remove surface stains and residues. Effective for cleaning all stone and tile surfaces. Also removes factory applied waxes and floor finishes, coating sealers, light grout residue (including epoxy), rubber and pencil marks, light mineral deposits, ground-in dirt and most sealer residues. NanoScrub® is nontoxic, non-flammable and non-acidic.
Aqua Mix No VOC (Volatile Organic Compound Formulas) help provide better indoor and outdoor air quality compared to similar traditional products.
USES:
Porcelain, ceramic, polished and unpolished natural stone (such as granite, limestone, marble, slate, and travertine), grout, quarry, saltillo, terra cotta, cement pavers, masonry surfaces, and other stone, tile and grout surfaces.
TEST A SMALL AREA:
According to application instructions to determine desired results.
APPLICATION:
1) Read entire label before beginning. SHAKE WELL BEFORE USING.
2) Sweep, vacuum, or dust surface to remove any loose debris.
3) Pre-wet surface with a liberal amount of water.
4) Apply NanoScrub® directly to the pre-wet surface.
5) Agitate with a white nylon pad, scrub brush or scrub machine.
6) Mop or wet vac up residue.
7) Rinse thoroughly with clean water. NanoScrub® can be used as a power booster, with Aqua Mix Heavy-Duty Tile & Grout Cleaner, Stone Deep Clean, or 1&2 Deep Clean mixed according to directions. Apply chosen product to surface, add NanoScrub® and agitate mixture. Continue to follow directions on the chosen product making sure a clean water rinse is the final step to remove any remaining residue.
LIMITATIONS:
Do not allow product to come in contact with any
non-recommended surface.
HANDLING AND STORAGE:
• Close container tightly after each use.
• Store in original container only.
• Store and use between temperatures of 40 ºF - 90 ºF
(4 ºC - 32 ºC).
• Keep unused material sealed tightly.
CAUTION:
MAY BE HARMFUL IF SWALLOWED. MAY IRRITATE EYES AND SKIN. Wear skin and eye protection. Contains coconut oil DEA, and ethoxylated alcohol. If in eyes, flush with water for at least 15 minutes. If on skin, wash with soap and water. If irritation persists, seek medical attention. If swallowed, DO NOT induce vomiting. Seek medical attention.
KEEP OUT OF REACH OF CHILDREN
Limited Product Warranty Custom Building Products (“Custom”) warrants to the original consumer purchaser that its product shall be free from defects in material and workmanship under normal and proper usage for a period of one year following the date of original purchase. Custom’s sole liability under this warranty shall be limited to the replacement of the product. Some states, countries or territories do not allow the exclusion or limitation of incidental orconsequential damages, so the above limitation or exclusion may not apply to you. This warranty will not extend to any product which has been modified in any way or which has not been used in accordance with Custom’s printed instructions. Custom makes no other warranties either expressed or implied. This warranty gives you specific legal rights, and you may have other rights that vary from state to state or from one country/territory to another.
COVERAGE:
Approximately 200 to 2,000 sq. ft. (19 m2 to 200 m2) per gallon (3.8 L).
MSDS
Sign In
